Media Articles

Crosby Straightpoint

Note our new address: 123 Proxima Park, Houghton Avenue, Waterlooville, Hants, PO7 3DU

  This email address is being protected from spambots. You need JavaScript enabled to view it.

 UK: +44(0)2392 484491    USA: +1 918 834 4611

wireless loadshackle

SP Loadshackle Supports Research at Tree Climbing Championship

A 6.5t capacity wireless loadshackle from Straightpoint (SP) was used to measure loads during competitors’ ascents at this year’s International Tree Climbing Championship (ITCC), which took place 28-30 July at the U.S. National Arboretum in Washington, D.C.

More than 60 of the world’s best male and female professional tree climbers representing 13 countries competed for the title of world champion. The International Society of Arboriculture (ISA) provides training and education on safe work practices for tree care providers; especially for those working aloft. Organized by ISA and presented by The Davey Tree Expert Company, the event was free and open to the public.

wireless loadshackle treeclimbingThe SP Wireless Loadshackle was used in the Ascent Event, which tests a competitor’s ability to efficiently and safely use their selected and approved ascent system. The event assesses competitors’ efficiency in attaching the ascent system to the ascent line(s), ascending to the bell, and transferring into a descent system. The actual descent is not part of the event. Points are earned for speed as well as for meeting predetermined safety objectives.

Dr. Brian Kane, Professor of Arboriculture in the Department of Environmental Conservation at the University of Massachusetts in Amherst, explained that the loadshackle was installed between the haul rope and the rigging hub. The ascent lines are attached to an attachment point, controlled by a ground technician using the haul line. Additionally, an overhead belay system is in place and competitors are on belay at all times while aloft.

Kane, who’s university position was endowed by the Massachusetts Arborists Association, was collecting data as part of an ongoing research project supported by the TREE Fund, which works to sustain the world’s urban forests by providing funding for scientific research, education programs, and scholarships related to arboriculture and urban forestry. He said: “This was a convenient event [to gather the data]. I have volunteered at the championships in the past. This was the first time we have used loadshackles in such a way but we will do so again.”

The ITCC showcased arborists in action and helped to educate consumers about professional tree work, and the training and expertise it requires to be carried out safely.

SP’s Wireless Loadshackle provides a solution to limited headroom applications. Each loadshackle is proof tested, then equipped with a hard anodized aluminum electronics enclosure. Kane used the loadshackle with the SW-MWLC software package allowing him to perform load tests at a safe distance, reading data on a laptop.

SP’s Impact Block, which measures the shock load and weight of branches as they are cut during felling or maintenance, is another product targeted at the arborist sector. The load cell is manufactured in partnership with tree safety equipment pioneer DMM. The aesthetic curves of the Impact Block combine with strength and durability to ensure a rope-friendly surface. Utilizing wireless dynamic load monitoring electronics and strain gauge technology, real time data can be displayed on a handheld controller, tablet or laptop. It eliminates the estimation work that often goes into arborist applications.

clamp on line tensionmeternl

Straightpoint to Take Centre Stage at Speedy Expo

Straightpoint (SP) will showcase its range of force measurement equipment and enter its latest innovation for the Star Products award at the Speedy Expo, which takes place 1-2 November at Exhibition Centre Liverpool’s ACC complex in the UK.

Equipment hire firm Speedy staged the event last year on the iconic waterfront and will again combine seminars, an exhibition and networking for suppliers and users of tools, specialist hire equipment, plant and support services. SP will exhibit at Stand F40 in close proximity to the networking zone and Star Products area.

SP will show a full range of equipment, but has chosen one for the award: a new product for measuring tension on static lines—the Clamp On Line Tensionmeter (or COLT)—with a state-of-the-art Bluetooth load monitoring app among a myriad of standout features. Already in Speedy’s hire fleet is SP’s most popular product, the Radiolink plus digital load indicator, but the COLT will be unfamiliar to many visitors.

David Mullard, business development manager at Straightpoint, said: “This is the first time we’ve exhibited at the event. In addition to the [aforementioned] products, we’ll show a 50t Loadlink plus and smaller 5t links to allow visitors to get hands-on with the equipment. Wireless compression load cells will also be part of the product centric exhibit.”

He added: “Speedy is one of our largest UK customers; we have a long-standing relationship over several years. They have for a long time trusted SP Loadlink plus and Radiolink plus dynamometers for safe lifting, LOLER testing, overload prevention and force measurement.”

The Radiolink plus—a 50t version will be on show—is primarily used in weighing, load monitoring and load testing applications. Mullard pointed to key features such as the wireless readout, allowing the user to be a safe distance from the load (up to 700m), and IP67 ingress protection against dust and water. Units take standard AA batteries, facilitating a simple change between hires, and are suited to dynamic testing and monitoring multiple lifting points on one display.

The COLT, meanwhile, is a manual, lightweight tool for measuring wire rope tension on guy wires, cable barriers, overhead lines, fall arrest systems and zip lines. Mullard said users benefit from a lack of cables and lauded its Bluetooth capability. “It’s the most efficient way to measure wire rope tension in the field, store results and send them back to the office, eliminating the need for paperwork,” he added.

The COLT measures tension on wire rope up to 11,000 lbf (lb. force) / 5,000 kgf (kg force) and up to 1 in. / 25mm diameter. It clamps onto pre-tensioned wire ropes, eliminating the need for additional sheaves or tooling, as is the case with alternative solutions.

Mullard said of the state of the UK hire market: “It’s buoyant and dynamic, but always in flux. Speedy has great geographic coverage, a young fleet of rental equipment as well as regional lifting centres of excellence. For the largest customers and projects, Speedy manages on-site facilities to provide the best possible levels of support and service. I expect the expo to provide widespread opportunity to refresh knowledge, make connections, meet contacts and learn.”

Visit SP at Stand F40.


Compression Load Cells Monitor Weight of Stories Above

Washington Universitys Olin Library

Eight 150-ton capacity Straightpoint compression load cells, supplied by Lifting Gear Hire (LGH), were integral to completion of a donor-funded, $18 million transformation project at Washington University’s Olin Library in St. Louis, Missouri.

sp wireless compression load cells in washington library buildThe project will eventually increase the quantity and variety of seating, study, and research spaces for library users; establish a new north entrance; increase special collections exhibition and storage capacity; and enhance the accessibility and visibility of specialized research services and special collections. Newly created spaces are slated to be open in time for the fall 2017 semester.

The project included excavation below a café and an expansion of the cafeteria that will provide additional seating, study, and social spaces. New and updated spaces will become a vibrant hub of research expertise and support for faculty, graduate students and undergraduates.

Special Inspections & Design was contacted by fellow St. Louis company Alberici, the general contractor on the project, to support the second, third, and fourth floors of the precast concrete library building.

Steven Fults, principal engineer and co-owner at Special Inspections & Design, explained that three quarters of the building had a below-grade basement but the fourth was concrete slab-on-grade. While excavating soil from beneath the fourth quadrant, it was revealed that the original concrete piers (placed in 1960) did not bear on bedrock, only onto a limestone ledge that was, say, 2 ft. thick.

SP load cells displayed the actual applied forceThus, Alberici had to shore up ¼ of the building and remove / replace 15 columns while the library stayed in service for students. Fults and his team presented a solution involving 400,000 lb. capacity scaffold towers on each side of these columns with W27 x 109 (depth of 27 in. and a normal weight per foot of 109 lb. f / ft.), 20 ft.-long longitudinal I-beams. Enerpac hydraulic rams, also supplied by LGH, were positioned on each of the four corners to apply load until they matched the dead load of the floors above.

Fults said: “The rams shored up the building from under the ceiling of the second floor. We wanted to match at least 90% of the weight or within 1000 lbs. of it. It meant the load cells played an integral role in providing continuous readout of the weight wirelessly to a computer. Each load cell was positioned in the middle of a beam in contact with the ceiling; we energized these beams and they pushed the ceiling upward, adding weight in 1,000, 5,000, or 10,000 lb. increments.”

The SP load cells displayed the actual applied force to the nearest 5 lbs. The latest version of Enerpac’s synchronous lifting system can integrate SP wireless load cell data directly into the controller.

A concrete saw was used to cut the old columns out, at which point that portion of the structure was resting on the load cells and rams connected to a hydraulic pumping unit on a trailer, 200 ft. away. Sometimes the team was working on four columns at a time, hence the requirement for eight load cell units.

Fults said: “When we cut the column out, Alberici demolished the underside with jackhammers, poured a new column foundation with cement, and set a new steel column. We poured high strength grout to fill the gap at the top. Supported by continuous readout from the load cells, we backed the hydraulic rams off slowly.”

He added: “The load cells were like watchdogs; at times all we needed to do was get updates first thing in the morning on elevations and weights. A standout memory from the project was the impact sunlight had. When the sun hit the building, weights fluctuated by several thousand pounds. It was apparent that the reinforced concrete building shifted loads internally within the redundancy of the structure.”

Load Cell Measures Dredging Line Tension

sp load cell used on lagoons ponds facility

A 2.5-ton capacity SP Radiolink plus load cell measures tension on a line stretching across a lagoon, upon which a dredge travels at a biosolids management facility, part of the City of Eugene Waste Water Dept., in Oregon, U.S. The RLP was added to inventory at the start of the latest six-month biosolids management season in March, where it replaced a dynamometer that was not suited to working in the elements.

dredge travels line

The load cell is connected to a land-based lateral move system that allows the dredge to move from side to side as well as forwards and backwards to harvest biosolids in the lagoon. Biosolids management relates to treated sewage sludge that is intended to be used as soil amendment.

The Radiolink plus boasts a separate internal sealed enclosure providing the load cell's electronic components with IP67 environmental protection even with the battery cover plate missing, making the dynamometer suitable for use in the harshest environments. Measurements are taken on a wireless Hand Held Plus in the cab of the dredge.

connected lateral boom

Due to the nature of the environment and exposure to corrosive hydrogen sulfide (H2S), SP took extra precautions to protect the delicate strain gauges and electronics by coating the internal components of the load cell with a special epoxy resin resistant to H2S. Contrail Smith, a lead at the biosolids management facility at City of Eugene Waste Water Dept., said, “The dynamometer we were using previously was hard-wired and wasn’t suited to working in the elements.

The RLP gives us both the luxury of wireless information and durability in outdoor application. It’s performed well this season and we’re pleased we found the product during online research during our off-season.” He added, “We monitor the tension on the line as a safety measure; we like to keep the tension around 2,000 lbs. of tension, so the operator keeps an eye on the Hand Held Plus whilst dredging. During the season, the dredge is operational every day for six months—that’s over 180 days—so we need to work with equipment that is reliable; the RLP fits that requirement.” Smith explained that the City of Eugene Waste Water Dept. is likely to be among the first of its kind to apply a load cell to such dredging applications. He said, “We are often visited by our peers from other sites and find that they apply our methods and technologies to their own facilities. I don’t know how many, if any, other sites are using load cells but it’s not likely to be commonplace.”
The lagoons (or ponds) at the facility measure 675 ft. long by 275 ft. wide.

SP Load Cells Provide Data for Ship-to-Shore Crane Project

port of LA

Lifting Gear Hire (LGH) provided 16 wireless compression load cells from Straightpoint to perform benchmark weighing as 10 ship-to-shore cranes were raised 10m by Shanghai Zhenhua Port Machinery Company (ZPMC) at Port of Los Angeles.

The 150-metric tonne capacity load cells combined to weigh one Noell ship-to-shore container handling crane, originally estimated to have a weight of 1,350te, and provide benchmark data before it and nine other cranes were to be raised by APM Terminals to accommodate larger ships calling at Pier 400 of the port.

sp compression load cells at port of LA

The project, managed by ZPMC North America, involved raising the cranes slightly more than 10m and inserting longer leg sections; it was a collaborative effort between the crane’s original equipment manufacturer (OEM) and ZPMC. Structural fabrication of the new leg sections and frame bracing was accomplished at ZPMC’s Shanghai facility.

sp compression load cells2

Rick Pope, vice president at ZPMC North America, explained that a key part of the project included benchmark weighing of one raised crane to determine the new, as-built weight and center of gravity. He said: “From this data, the crane OEM calculated the required concrete ballast that needed to be added to establish the crane’s designed operational center of gravity and stability. The results became the basis of ballasting for the other cranes being raised.”

The weighing procedure included lifting the crane utilizing ZPMC’s self-propelled modular trailers, placing the load cells in pairs under the eight intermediate gantry equalizers on specially designed pedestals, and lowering the crane down to rest on the load cells. The crane was lifted off the load cells between trials to allow for three distinct weighing evolutions.

The initial as-built weight of the crane as provided in historical documents was 1,185te. Post-construction weighing indicated the raising added 193te, for a total pre-ballast weight of 1,378te. Concrete ballast was added according to OEM specifications and resulted in a post-ballast weight of 1,414te and shift of the operational center of gravity approximately 1m toward the rear of the crane.

LGH also provided a rugged SP wireless tablet with data logging software and USB wireless base station. The data logging software provided user-configurable screens, recording the physical location of the load cells and collection of data. Center of gravity software collected data over three trials of weighing to calculate an average. A report was automatically created upon completion of the tests, including each load cell’s load, location, calculated center of gravity and standard deviation of weight data.

John Molidor, director of projects and market development at Straightpoint, said: “It was great to witness the application in person and get a first-hand impression of the 16 load cell system delivering safety and accuracy to such a landmark project. We enjoyed working with LGH and ZPMC North America to deliver the state-of-the-art solution.”

Please let us know your name.

Invalid Input

Invalid Input

Invalid Input

Please let us know your email address.

Your email does no match please enter again

Invalid Input

Invalid Input

Once you have sent this form it will instantly reach a Crosby SP representative, directly, who will respond to your enquiry by email asap. Or if you would prefer a call back please let us know in the message.